WiCardKit 1.0 Software - Programmer and USB to Serial interface

Other projects from this group

WiCardKit 1.0 Software - Programmer and USB to Serial interface

Windows software which handles “WiCardKit 1.0 board”. AVR high voltage (parallel) and a USB to Serial interface programming ESP32/ESP8266...

WiCardKit 1 Programmer - rev 1.1


Price:

 

Other projects from this group

 

The high voltage (parallel) programming method is the highest layer of access to the microcontroller memories and programming. This method can unlock the AVR/PIC chips which can’t be programmed by regular programmers while the chips work well.

The other feature is the “reset” pin in some the microcontrollers can be accessible as an IO with high voltage programming.

High voltage means a voltage a bit more than the typical voltage of the microcontroller which is 12V for the AVR microcontrollers and 13V for the PIC microcontrollers.

This voltage can only be applied on the “reset” pin under the specific condition.


WiCardKit 1.0, Software features

This software contains tools for the programmable based circuit designs, such as the circuit with microcontrollers or arduino and etc.

In the current revision, in addition to the AVR parallel programmer, there is a USBtoSerial interface which lets the user to upload the programs on espressif modules.

The following AVR microcontrollers can be programmed with the high voltage method:

ATtiny13A

ATmega48P

ATmega48V

ATmega8

ATmega8A

ATmega8L

ATmega88P

ATmega88V

ATmega16A

ATmega168P

ATmega168PV

ATmega32A

ATmega328P

In the “WiCard Kit 1.0 WinDriver” folder there is a driver installation file. After plugging the USB cable of the WiCardKit board, install the driver.

  • Also you can install the driver manually from “Driver” folder and device manager
  • After the driver installation, unplug the board’s USB cable then plug it again after 30 seconds

wicardkit 1 software com port usb2serial

In case the driver has been installed probably, you can see the device’s COM port in the device manager window.


Software Installation

To installation go to “Software Bin” folder and click on “setup”, then in the installation window, click on “Install”.

wicardkit 1 hardware install

The software will be installed automatically and a shortcut icon will be added on your desktop. It will run automatically right after setup and will ask you to select “COM” port.


Hardware Detection

After plugging the WiCardKit 1.0 board USB cable, select the COM port of the board.

wicardkit 1 hardware avr parallel programmer

In case everything is ok, “WiCardKit 1.0 Found” will be appeared in the bottom of the window.


Chip Programming

For the chip programming, first select your chip from “chip selection” drop down menu.

The “Dip Switch” configuration of the board will appear and configure the switches.

You can choose and select one of the .hex, .rom and .bin forma files for the flash and .hex, .eep, .bin for the eeprom memory programming.

In the “Fuse and Config Bits” section you can see and set the lock and fuse bits value.

The “Device IDs and Status” section show microcontroller IDs and calibration bytes.

wicardkit 1 hardware high voltage programmer

“Check” button reads the Device IDs, calibration, lock and fuse bytes.

“Erase and Unlock” erases the flash memory (and eeprom if eesave is not programmed) and then set the fuse bits to default, so the chip can be programmed with regular serial programmer.

“Program and Verify” erases the flash memory and then programs the selected files into the chip and finally will program the fuse bits if have been set.

“Read EEprom” reads the eeprom memory and saves it as a .bin file.

“Read Flash” reads the flash memory and saves it as a .bin file

“Write Config/Fuse” programs the fuse and lock bit data.

1.0

- The UI design

- Programming

- Future features prediction


Similar Projects: